The Ghost Immobiliser
Immobilisers are a potent weapon in the fight against vehicle theft. They prevent vehicles from being started without a key fob, and are effective in stopping hotwiring as well as traditional methods of vehicle theft. Modern methods such as key cloning and relay theft are becoming more common.
The Ghost Immobiliser was designed to counter these new trends and make your car unnoticeable. It doesn't rely on LED indicators, radio signals or key fobs. It is quiet and discreet.
Easy to install
The Ghost Immobiliser is a revolutionary device, connects to the CAN data network of your vehicle to prevent key cloning or theft. It is an TASSA approved product, and is recognized by insurance companies. It is silent and virtually undetectable to thieves. It uses buttons in your steering wheel, centre console, and door panels to make an individual pin code that must be entered before you can start your car. You can create up to 20 different sequences for increased security. The system is simple to install and doesn't require any additional hardware.
To ensure the best possible outcomes It is recommended that you choose a reputable CAN-immobiliser installer who is specialized in your particular vehicle. Ideally, they'll have a workshop in your area where you can visit to get your installation done. There is also an array of tools and equipment that can help you with the installation. They will have basic hand tools, multimeters, insulation tape and heat shrink tubing to protect the connections. A user's manual will provide you with instructions for the wiring in your vehicle.
Before starting the installation Before beginning the installation, disconnect the battery to avoid short circuits and airbag deployment. It is important to double-check the location of the CAN H and CAN L wires, since the wrong identification could result in unintentional system integration. It is also a good idea to label or mark the wires. Also, utilize a multimeter for verification that the identified power source provides a consistent 12V supply.
Advanced thieves employ a variety of strategies to get around Ghost Immobilisers, including blocking or spoofing. These methods work by amplifying the signal that is sent from your key fob to the electronic control unit of your vehicle. With advanced anti-jamming technologies and vigilant monitoring, your vehicle can be protected from these sophisticated attacks.
Security Improved
Ghost immobilisers are an additional layer of protection for your car against theft. car immobiliser ghost is a PIN protection system that is entered by pressing buttons on your dashboard or steering wheel, making it harder for thieves to steal your car. The device is designed to be hidden inside your vehicle. It has no lights or other indicators to alert potential burglars to its presence. It communicates with your car's ECU through the data bus, so it is not susceptible to the same hacking and relay attacks that could disable traditional security systems.
ghost immobiliser fitter is a valuable investment for those who own high-end vehicles, as they are at greater risk of theft due to their worth and the popularity. Its enhanced security features protect against key copying, ECU swapping, and other threats to your car's security. Ghost immobilisers can be connected to apps, which means you can arm or disarm easily. They can also have the option of a service/valet mode, which permits you to temporarily disable them while your vehicle is being repaired or serviced.
A ghost immobiliser has another great feature: it doesn't require any cutting of wire. This is an excellent option, particularly if your vehicle is newer and does not include an immobiliser. Certain systems are capable of integrating with the GPS tracking device, thereby providing an additional layer of security to your vehicle. The use of a GPS tracker may also help you reduce the cost of insurance. If you decide to purchase a ghost immobiliser be sure it is TASSA verified and a professional installer will install it for you.
Compatible with all major models and brands
The Ghost Immobiliser was designed to work with all major vehicle models and makes, protecting your precious possessions from theft. It creates a unique pin code using buttons on your steering wheel, console, or door panels. You must enter the code before you can drive. The system is tamper-proof, undetectable, and is covered by a three-year warranty. It is also fully endorsed by insurance companies. This means that you will be able to lower your cost of insurance.
The Ghost system differs from the normal immobilisers, which use the key fob to provide ignition control. It is connected directly to the engine controller via the CAN bus. It is virtually impossible to remove, disable or hack. In addition it is possible to use the Ghost system can be linked with an secure iPhone application that permits remote management and monitoring.
You can create a PIN that is easy to remember, but mathematically unattainable to thieves. You can customize and change the PIN at any time to protect your vehicle even when it's parked in a parking lot or on the street. You can also select a valet or service mode if you need someone other than you to drive your car temporarily such as when it's in garage for maintenance. This feature can also to prevent your vehicle from being stolen by a dishonest mechanic. You can choose a Ghost Call alert to give you more security. It will notify you when your vehicle is moving or has been moved.
Convenience
The ghost immobiliser protects your vehicle from common theft methods like key cloning or relay attacks. It works by connecting to the vehicle's data network CAN, and preventing communication with the engine ECU. This makes it very difficult for thieves to hack or clone your vehicle.
Once installed, you'll have to enter a PIN of up to 20 digits long using the buttons on the dashboard as well as the steering wheel to begin the vehicle. The system is completely hidden and undetectable to thieves, as it does not emit any radio frequency signals. It can be set up using a PIN code that can be changed by the user, adding to its security. The system is designed to avoid circuit-cutting, making it almost impossible to alter.
If you get lost in your PIN, there are systems that let you communicate with the immobiliser using an app on your phone and instantly disarm it. Some systems even have a service/valet setting that allows you to start your car, for instance, if you drop it off at Valet Park or a garage.
The Ghost Immobiliser also is undetectable by thieves, as it does not transmit radio signals. This is a significant advantage over other security systems that are sold aftermarket. It is also simple to use, and doesn't require complicated wiring. It can be used conjunction with dash cams for added safety. Dash cam Thinkware F70 features clear and crisp 1080p HD footage Format Free Technology, and parking mode. The system is able to be hardwired to guarantee maximum performance and longevity.
Installation
It is crucial to select the most reliable immobiliser ghost in order to safeguard your vehicle from thieves. This device can stop car thefts by blocking communication between key fobs and the engine controller unit. This prevents thieves from intercepting the signal and copying your key fob in order to start your vehicle. It also detects the moment it has been altered with and alert the owner of the vehicle.
The device is simple to install and can be used with the existing systems of your vehicle. It doesn't require any modifications to wiring in your vehicle and can be placed in a hidden place like under the dashboard. To ensure that the device is properly installed, follow the instructions in the manual for the user. After installation, it's crucial to test the system. This will ensure that the immobiliser ghost works in the way it is intended.
You can purchase an Autowatch Ghost 2 immobiliser, and have it installed by a reputable installer. The installer will connect the Ghost to the CAN Bus network in your vehicle, which makes it difficult for thieves to steal or disable the system. The installation process typically takes between 2 and 3 hours.
It is recommended that you consult the wiring diagram of your vehicle during the installation process. This will allow you to locate the CAN High and CAN Low wires that are required to connect the Ghost to the engine of your vehicle. Double-check all connections to ensure that they're secure and insulated.
Once the installation is complete after which you can use the Ghost Immobiliser in normal operation. It will turn off the ignition of your vehicle if it is not able to start it with the correct PIN, which you will need to enter yourself. The ghost cost of immobilisers can also be set to service/valet mode when you have to hand over your vehicle for servicing or valet parking.